Campbell SDM-CD16AC Dokumentacja

SDM-CD16AC 16 ChannelAC/DC ControllerRevision: 12/08Copyright © 1987-2008Campbell Scientific, Inc.

SDM-CD16AC 16 Channel AC/DC Controller DeviceNeutral (-) Hot (+) NO NC COM FIGURE 4. Typical Wiring Application 4.1.3 Motor Control The SDM-CD16A

SDM-CD16AC 16 Channel AC/DC Controller Datalogger PS100 POWERSUPPLYFIGURE 5. SDM-CD16AC Relay Outputs to MCC 5. Address Selection Switches Each SDM

SDM-CD16AC 16 Channel AC/DC Controller 01230123BAADDRESSES FIGURE 6. Addressing 6. Datalogger Programming In CRBasic, the SDMCD16AC instruction is u

SDM-CD16AC 16 Channel AC/DC Controller controlled). As an example, with the array CDCtrl(32), the value held in CDCtrl(1) will be sent to port 1, the

SDM-CD16AC 16 Channel AC/DC Controller default, minimum allowable, and maximum bit period for each of our CRBasic dataloggers. TABLE 3. Bit Period Va

SDM-CD16AC 16 Channel AC/DC Controller 6.2 Edlog Programming Instruction 104⎯SDM-CD16AC use with CR23X, CR10(X), and 21X Param. Type Description 1

SDM-CD16AC 16 Channel AC/DC Controller The first 8 bits clocked out represent the SDM-CD16AC address. If the address matches the SDM-CD16AC's ad

SDM-CD16AC 16 Channel AC/DC Controller The program assumes the temperature measurements have been made, and the average temperature for each greenhous

SDM-CD16AC 16 Channel AC/DC Controller If (Temp(I) >= 27.5) Then Cool(I) = 1 ElseIf (Temp(I) < 24.5) Then Cool(I) = 0 End

SDM-CD16AC 16 Channel AC/DC Controller ElseIf (Temp(I) < 24.5) Then 'Set appropriate Cooler Bit Low: CD16_Output = CD16_Output AND

Warranty and Assistance The SDM-CD16AC 16 CHANNEL AC/DC CONTROLLER is warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and

SDM-CD16AC 16 Channel AC/DC Controller Input Location assignments are as follows: Input Location Location Label Description 1..5 Temp #1..#5 Avg te

SDM-CD16AC 16 Channel AC/DC Controller 9: Else (P94) Else, If the heater is off, 10: Z=F (P30) 1: 0 F Enter a "0" into he

SDM-CD16AC 16 Channel AC/DC Controller 21: End (P95) End Then Do/Else/End END COOLER CONTROL LOGIC START FAN CONTROL LOGIC BASED ON HEATER/COO

SDM-CD16AC 16 Channel AC/DC Controller 32: If Flag/Port (P91) If flag 2 is set 1: 12 Do if flag 2 is high 2: 30 Then Do Then 33: Begin

SDM-CD16AC 16 Channel AC/DC Controller 20

This is a blank page.

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com info@campbells

SDM-CD16AC Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks ta

SDM-CD16AC Table of Contents ii Tables 1. Datalogger to SDM-CD16AC Connections... 4 2. Base 10 to Base 4

SDM-CD16AC 16 Channel AC/DC Controller 01230123ADDRESSESGNDC1C2C3+12VAUTOONOFF16151413121110987654321AUTOONOFFC2C2C216C2C2C216C2C2C216C2C2C216C2C2C216

SDM-CD16AC 16 Channel AC/DC Controller 2. Control Specifications Operating voltage: 12 VDC nominal (9 to 18). Current drain at 12 VDC: 6 mA quiesce

SDM-CD16AC 16 Channel AC/DC Controller EXTERNAL 9 TO 18 VDC + —SDM-CD16AC DATALOGGER 12 V GND C1 or SDM-C1 C2 or SDM-C2 C3 or SDM-C3 Connect

SDM-CD16AC 16 Channel AC/DC Controller Cables connecting the terminals of the datalogger and SDM device should be kept as short as possible to minimiz

SDM-CD16AC 16 Channel AC/DC Controller The order in which connections are made is critical. Always connect 12 V first, followed by ground, then Contr