Campbell NL100 Dokumentacja

NL100/105 Network Link InterfaceRevision: 12/10NL100NETWORK LINK INTERFACEPOWERRS485Logan, UtahRS485CS I/OCS I/ORS232RS232LANLINK10 BASE TMADE IN US

NL100/105 Network Link Interface The boot jumper is shown in Figure 2 below. The NL100/105 ships with this jumper connected to only one post. Place th

NL100/105 Network Link Interface 2.3 Port Configuration An important step in configuring an NL100/105 for use is setting up the communication port(s)

NL100/105 Network Link Interface The NL100/105 prompt lists all of the available menu options. Only the first few characters of the main menu options

NL100/105 Network Link Interface TcpSer - The NL105 acts as a serial server for the TLink port. A serial server is a device that allows serial communi

NL100/105 Network Link Interface If both the beacon interval and verify interval are set to 0, a verify interval of 5 minutes will be used. RS485 Neig

NL100/105 Network Link Interface CR10X, CR510, CR23X, 21X, and CR7 dataloggers ship with a mixed array operating system. Mixed array dataloggers do no

NL100/105 Network Link Interface CS I/O SdcAddr/bps - This option is used to set up the CS I/O port to communicate with the datalogger as an addressab

NL100/105 Network Link Interface Config” option must be enabled (Section 2.4.3.7) or you will not be able to communicate with TCP/IP through the NL100

NL100/105 Network Link Interface RS-232 serial server port number - Enter the port number, in the range of 1 to 65000, that will be used for communica

NL100/105 Network Link Interface 2.4.3.6 PakBus Address of the NL100/105 If the NL100/105 is to be used as a router in a PakBus network, a PakBus Add

Warranty and Assistance The NL100/105 NETWORK LINK INTERFACE is warranted by Campbell Scientific, Inc. to be free from defects in materials and workma

NL100/105 Network Link Interface take place over a port other than the Ethernet connection, this setting can be disabled. When enabled, there is one o

NL100/105 Network Link Interface By default the address is 0. To enable security, enter a value between 1 and 65535. 2.4.4 Defaults The Defaults opti

NL100/105 Network Link Interface 2.4.5 Reset This option reboots the NL100/105, using the last saved settings that have been programmed by the user.

NL100/105 Network Link Interface 2.4.9 Serial Server Watchdog If no communication is detected for a specified number of minutes, the NL100/105 will d

NL100/105 Network Link Interface Some of the communication links require additional peripherals or cables that can be purchased from Campbell Scientif

NL100/105 Network Link Interface 3.2.2 MD9 Connection from NL100/105 to Datalogger Campbell Scientific's MD9 Multidrop Interface can be used to

NL100/105 Network Link Interface 3.2.3 MD485 Connection from NL100/105 to Datalogger Campbell Scientific's RS485 communication device, the MD485

NL100/105 Network Link Interface Setup window for an RF Network using VHF/UHV radios and a mixed array datalogger. FIGURE 5. LoggerNet Setup for NL1

NL100/105 Network Link Interface In the LoggerNet communications software, the phone modem on the NL100/105 side should be shown attached to the IPPor

NL100/105 Network Link Interface FIGURE 7. PC9000 Setup for TCP/IP Communication 3.3.2 Hardware Setup for NL105 Communication with the CR9000 via TL

NL100/105 Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks tab

NL100/105 Network Link Interface 26

Appendix A. CS I/O Port The CS I/O port is Campbell Scientific's input/output port. It is not a standard RS-232 pin-out. The following table pro

This is a blank page.

Appendix B. Null-Modem Cable A null-modem cable allows communication between two similar devices. It is sometimes called a crossover cable, because t

This is a blank page.

Appendix C. 10 Base-T Cabling The cable that runs from the computer to the NL100/105 should be a Category 5 twisted pair cable. If the NL100/105 will

This is a blank page.

Appendix D. RS-485 Connector, 3-Pin Terminal Block The RS-485 port is for connecting an MD485 multidrop interface to the NL100. The MD485 attaches t

This is a blank page.

Glossary Beacon Interval - Devices in a PakBus network may broadcast a message to other devices, in order to determine "neighbor" devices. N

NL100/105 Table of Contents ii 3.2.6 Phone Modem Connection from NL100/105 to Datalogger ... 23 3.3 NL100/105 to Datalogger Connections - CR900

This is a blank page.

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbel

NL100/105 Network Link Interface 1. Introduction The NL100 and NL105 Network Link Interfaces are devices used to communicate with Campbell Scientific

NL100/105 Network Link Interface NL100NETWORK LINK INTERFACEPOWERRS485Logan, UtahRS485CS I/OCS I/ORS232RS232LANLINK10 BCorner ScrewsASE TMADE IN USAS

NL100/105 Network Link Interface Power Supply Requirements The NL100/105 is powered via the green G 12V connector (11 to 16 VDC at 140 mA average curr

NL100/105 Network Link Interface 2.1 Computer to NL100/105 Physical Connection An RS-232 null-modem cable is required to establish communication betw

NL100/105 Network Link Interface You can also use the Terminal tab in DevConfig to set up the NL100/105 using the menus, as explained in the following