Campbell RavenXTG GPRS/EDGE Podręcznik Użytkownika Strona 78
- Strona / 131
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Raven EDGE/GPRS for Cingular - User Guide, version 2.31 73
AT Commands: UDP
This group includes commands specific to UDP communications.
FIGURE 1. Common : UDP
AIP=n
HOR=n
MDhh
UDP
Allow IP address.
n=0 Allow only the IP address specified in S53 to connect when UDP auto answer is enabled (S82=2).
n=1 Allow any incoming IP address to connect when UDP auto
answer is enabled (S82=2).
Note: Always subject to any Friends filters that may be defined.
Half-Open Response - In UDP auto answer (half-open) mode:
n=0 No response codes when UDP session is initiated.
n=1 RING CONNECT response codes sent out serial link
before the data from the first UDP packet.
Note: Quiet Mode must be Off.
Default power-up mode for the serial port.
When the Raven is power-cycled, the serial port enters the mode specified by this
command
after 5 seconds. On startup, typing ATMD0 within 5 seconds changes the mode to normal (AT
command) mode.
hh (hex byte)=00 : no
r
mal mode
- Raven EDGE/GPRS 1
- Important Notice 2
- Safety and Hazards 2
- Limitation of Liability 2
- Warranty Summary 2
- Contents 3
- EDGE/GPRS Overview 6
- Internet 7
- Common Uses for the Raven 8
- Automation and Telemetry 9
- Activation of the Raven 10
- Inserting the SIM 11
- Utilities for the Raven 15
- Wireless Ace 16
- Modem Doctor 18
- IP Manager and DNS 19
- Fully Qualified Domain Name 20
- Dynamic Names 21
- Configuring DNS 23
- PPP-Peer 23
- FIGURE 1. Wireless Ace: MD 26
- PassThru Mode 27
- FIGURE 3. Wireless Ace: MD 28
- UDP Pad 30
- Reliable UDP 31
- UDP Multicast Mode 31
- TCP PAD 32
- Hybrid Modes 33
- Public and Private Mode 33
- Keepalive 34
- Data usage using Keepalive 35
- Modbus/BSAP Configuration 36
- Configuring the Raven 38
- Dynamic IP 40
- Dynamic IPs 42
- Hardware Installation 45
- Raven Indicator Lights 46
- Modem Placement 48
- AT Commands 55
- Direct Serial Connection 58
- AT Command Listing 61
- Information and Status 62
- FIGURE 2. Status Group 63
- AT Commands: 66
- Misc (Miscellaneous) 66
- AT Commands: Serial 69
- AT Commands: TCP 76
- AT Commands: UDP 78
- AT Commands: DNS 81
- AT Commands: Dynamic IP 82
- AT Commands: PPP/Ethernet 84
- PPP/Ethernet 84
- AT Commands: PassThru 86
- PassThru 86
- SMTP (including SMS) 88
- *SMTPSEND=[email][body] 89
- AT Commands: Other 90
- AT Commands: Friends 93
- Friends 93
- AT Commands: Logging 94
- FIGURE 1. Telemetry 95
- IP List Dial 96
- Indicates 97
- FIGURE 4. MD menu 98
- FIGURE 5. S53 and *DPORT 98
- Destination Address 99
- Destination Port and *DPORT 99
- AT Commands: EDGE/HSDPA 100
- EDGE/HSDPA 100
- FIGURE 2. Modems 102
- FIGURE 3. Install New Modem 102
- FIGURE 4. Modem Driver 103
- FIGURE 5. Modem Port 103
- FIGURE 6. Finish 103
- Windows 104
- FIGURE 10. Connection Type 105
- FIGURE 13. Connection Name 106
- FIGURE 14. Phone Number 107
- FIGURE 16. Finish 108
- FIGURE 17. Connect 108
- Making a DUN Connection 110
- Windows 98 and Windows NT 111
- Simple Network Management 113
- Protocol (SNMP) 113
- Listening Port 114
- Security Level 114
- User Name and Password 114
- Trap Destination 115
- Warranty Terms 122
- Warranty Conditions 123
- Warranty Terms and Conditions 124
- General Conditions 124
- Technical Support 125
- AirLink Technical Support 131
Powiązane produkty i podręczniki dla Networking Campbell RavenXTG GPRS/EDGE
Networking Campbell SC32B Instrukcja Użytkownika
(12 strony)
(12 strony)
Networking Campbell NL200 Instrukcja Obsługi
(58 strony)
(58 strony)
Networking Campbell COM220 Dokumentacja
(38 strony)
(38 strony)
Networking Campbell SC932A Instrukcja Obsługi
(18 strony)
(18 strony)
Networking Campbell SM4M Arkusz Danych
(62 strony)
(62 strony)
Networking Campbell DC112 Instrukcja Operatora
(221 strony)
(221 strony)
Networking Campbell NL120 Instrukcja Użytkownika
(22 strony)
(22 strony)
Networking Campbell SDM-CAN Dokumentacja
(32 strony)
(32 strony)
Networking Campbell IPn3Gb Instrukcja Obsługi
(50 strony)
(50 strony)
Networking Campbell NL115 Instrukcja Obsługi
(48 strony)
(48 strony)
Networking Campbell SC-IRDA Instrukcja Obsługi
(14 strony)
(14 strony)
Networking Campbell SDM-CD16AC Dokumentacja
(26 strony)
(26 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji